![how to install transmission solenoids on a 09 accord how to install transmission solenoids on a 09 accord](https://m.media-amazon.com/images/I/61M0wFYhusL._AC_SL1200_.jpg)
Connect the left ball joint to the steering knuckle. Refer to Wheel Drive Shaft Replacement (See: Axle Shaft Assembly > Removal and Replacement).ġ7. Install the wheel drive shaft to the transmission. Refer to Steering Gear Replacement (See: Steering Gear > Removal and Replacement > Steering Gear Replacement).ġ6. Install the power steering gear mounting bolts. Refer to Transmission Front Mount Replacement (See: Transmission Mount, A/T > Removal and Replacement > Transmission Front Mount Replacement) or Transmission Rear Mount Replacement (See: Transmission Mount, A/T > Removal and Replacement > Transmission Rear Mount Replacement).ġ4. Raise the engine with the engine support fixture.ġ3. Hand start the bolts (3) and tighten the side cover bolts and stud to 28 Nm (22 lb ft).ġ1. Refer to the graphic in order to find the correct installation points of the bolts and the stud.Ĭaution: Refer to Fastener Caution (See: Vehicle > Vehicle Damage Warnings > Fastener Caution).ĩ. Install the 11 side cover bolts (3) or studs (4) (model dependent).Ĩ. Install the side cover assembly onto the transmission case.ħ. Retain the thrust washer with J 36850 or equivalent.Ħ. Install the side cover to drive sprocket thrust washer (7) onto the side cover.ĥ. Retain the seals with J 36850 or equivalent.Ĥ. Install the side cover gaskets (5 and 6) into the grooves on the side cover (1).ģ. If the seals were removed, thoroughly clean and dry the side cover seal grooves and the side cover seals.Ģ. Remove the two side cover gaskets (5 and 6) and the side cover to driven support thrust washer (7). Remove the transmission side cover (1).Ģ2. Remove the 11 transmission side cover bolts (3) or Studs (4) (model dependant).Ĭaution: Pry on the corner of the case side cover near the locating dowel pins (45), to prevent damage to the sealing surfaces.Ģ1. Lower the engine with the engine support fixture.Ģ0. Refer to Transmission Front Mount Replacement (See: Transmission Mount, A/T > Removal and Replacement > Transmission Front Mount Replacement) or Transmission Rear Mount Replacement (See: Transmission Mount, A/T > Removal and Replacement > Transmission Rear Mount Replacement).ġ8. Refer to Steering Gear Replacement (See: Steering Gear > Removal and Replacement > Steering Gear Replacement).ġ5. Remove the power steering gear mounting bolts. Refer to Wheel Drive Shaft Replacement (See: Axle Shaft Assembly > Removal and Replacement).ġ4. Remove the wheel drive shaft from the transmission. Refer to Front Fender Liner Replacement (See: Front Fender Liner > Removal and Replacement).ġ3. Refer to Tire and Wheel Removal and Installation (See: Wheels and Tires > Removal and Replacement).ġ2. Refer to Lifting and Jacking the Vehicle (See: Vehicle Lifting > Procedures > Lifting and Jacking the Vehicle).ġ1. Refer to Engine Support Fixture (See: Engine > Removal and Replacement > Engine Support Fixture).ġ0. Remove the transmission upper side cover bolts.ĩ. Refer to Park/Neutral Position Switch Replacement (See: Transmission Position Sensor/Switch, A/T > Removal and Replacement > Park/Neutral Position Switch Replacement).Ĩ. Remove the PNP switch lever nut and lever.ħ. Disconnect the shift cable from the PNP switch.Ħ. Remove the underhood electrical center bracket.Ĥ.
![how to install transmission solenoids on a 09 accord how to install transmission solenoids on a 09 accord](https://i.ebayimg.com/images/g/BG4AAOSw35hcXwgu/s-l640.jpg)
Remove the underhood electrical center from the bracket.ģ. Refer to Air Cleaner Assembly Replacement (See: Air Cleaner Housing > Removal and Replacement > Air Cleaner Assembly Replacement).Ģ. You will not be replacing the cover, just following the directions for removal and install.ġ. Note: The cover removal directions are for cover replacement. Also, to access the solenoids, you have to remove the side cover from the transmission. All attached pics correlate with the directions. The directions are broken into two sections, the 1-2 solenoid and 2-3. Here are the directions specific to your vehicle regarding the shift solenoids.